How to Run a Trade Show in a Tent

To run a trade show in a tent, start from the booth count you need, size the tent to fit those booths plus aisles, exits and service space, then plan the four things a building normally gives you for free: power, flooring, weather protection and code approval. In practice that means picking a tent style with as few interior poles as possible, drawing the layout to scale before you sign the rental, booking generators or shore power early, putting down a subfloor on grass, and getting your tent permit and fire marshal review on the calendar months ahead. This guide walks through each step with planning examples.
If you only need a quick size estimate, try the event tent size calculator. For the questions to put to your vendor, see questions to ask a tent rental company.
When a Tent Makes Sense
Tents solve real problems. They let you hold an expo where no hall exists, add exhibit space next to a full building, put a show on a fairground, farm, waterfront or parking lot, and keep the event close to the audience you want. They also add work. Every service a convention center bundles, from lighting and restrooms to load-in docks and climate control, becomes something you rent, schedule and pay for. Go in knowing the tent itself is often only part of the bill.
Step 1: Pick the Tent Style
The tent style decides where booths can go. The main options are:
- Frame or clearspan tents: No center poles, so the whole floor is usable. Clearspan structures come in wide spans and can be anchored with ballast on pavement. They are usually the best fit for a booth layout.
- Pole tents: Lower cost and quick to install, but they rely on center poles and need staking, which usually rules out asphalt. Poles land in your aisles or booths unless you plan around them.
- Rows of smaller tents: Some outdoor expos use a grid of 10x10 or 20x20 pop-ups or frame tents. This is flexible but harder to protect from weather and harder to light and power evenly.
Ask the vendor for a drawing with the exact pole, leg and anchor positions. You need it to lay out booths.
Step 2: Size the Tent From the Booth Count
Work backward from how many booths you plan to sell. A common planning rule is that booths take roughly half of the floor, and aisles, exits, entrances, registration, seating and service areas take the rest. Here is a worked example for a 60x120 clearspan tent (7,200 square feet):
- Perimeter rows: 10x10 booths along both long walls, 12 per side, for 24 booths.
- Center island: Two rows of back-to-back 10x10 booths running 100 feet, for 20 booths.
- Aisles: Two 10-foot aisles between the walls and the center island, plus a 10-foot cross aisle at each end.
- Subtract for exits and service: Remove 4 to 6 booths for side exits, an electrical distribution point and a first aid or info table.
- Planning result: About 38 to 40 sellable 10x10 booths.
That is about 4,000 square feet of booths in a 7,200-square-foot tent, a little over half. Your number will change with pole positions, wider booths, a stage or a food area. If attendance is high, widen the aisles before you add booths. For more on spacing, read our guide to trade show aisle width.
Step 3: Lay Out Booths, Aisles and Exits
A tent layout follows the same rules as a hall, with a few extras:
- Keep exits clear and marked: Tent codes usually require a minimum number of exits based on occupant load, spread around the perimeter, with lit exit signs. Never put a booth in front of a sidewall exit.
- Keep booths off the legs: Do not sell a booth with a tent leg or pole in the middle of it. Make those spaces storage, a seating spot or a sponsor sign.
- Leave room at the entrance: Entrances on the short ends need a landing area for lines, bag checks and the info desk.
- Think about the sun: On a hot day the side with the sidewalls rolled up is the side people stand. Put demos and seating where air moves.
- Number booths in a simple pattern: Odd numbers on one side of each aisle and even on the other help attendees find their way in a space with few landmarks.
Draw the layout to scale in event floor plan software using the vendor's tent drawing, then send it to the tent company, the electrician and the fire marshal so everyone works from the same plan.
Step 4: Plan Power and Lighting
Tents do not come with outlets. You will need either shore power from the site or rented generators, plus distribution panels, cables, cable ramps and a licensed electrician. Plan it in this order:
- Ask every exhibitor on the application what they need: a single 120-volt circuit, more amps, or nothing at all.
- Add tent lighting, HVAC or fans, any stage audio, registration and food service.
- Give the totals to your electrician or power vendor to size generators and panels with headroom.
- Mark where panels, generators and cable runs go on the floor plan, keeping generators away from entrances and air intakes.
- Cover every cable crossing an aisle with a ramp, and keep runs out of exits.
Sell power as a booth add-on so exhibitors who need more pay for it. Lighting matters too: tent interiors can be dim, so ask the vendor for lighting levels and expect exhibitors to bring their own booth lights.
Step 5: Choose the Flooring
On grass, dirt or gravel, rent a subfloor of interlocking panels. It levels booths, keeps water out, supports carts and gives wheelchair users a firm surface. Add carpet or turf on top for a finished look. On asphalt you can often skip the subfloor, but check for slope and drainage, because rain on a lot runs straight through a tent. Wherever flooring meets the ground, use edge ramps so nobody trips.
Step 6: Plan for Wind, Rain and Heat
Weather is the biggest risk at a tent show. Build a written weather plan with:
- Wind limits: Get the maximum wind the tent is rated for as installed, and a lower number at which you clear people out.
- A decision-maker: One named person, with a backup, who can stop the show.
- Monitoring: A weather service or app checked hourly during the show, plus lightning alerts.
- Shelter: A building or vehicles where people can go if you clear the tent.
- Sidewalls and gutters: Sidewalls you can close for rain and wind, and rain gutters between joined tents.
- Heat and cold: Fans, misting or air conditioning in summer and heaters in cold months. The tent heater calculator gives a starting estimate.
Share the plan with exhibitors in the exhibitor manual and at the morning briefing. Ask them not to tie anything to tent legs or sidewalls.
Step 7: Get Permits and Fire Marshal Approval
Most jurisdictions treat a large event tent as a temporary structure. Expect some mix of a tent permit, an electrical permit for generators and distribution, a fire inspection and, if you serve food, health permits. A typical submission includes:
- A site plan showing the tent, generators, fire lanes, hydrants and separation from buildings.
- A floor plan showing booths, aisle widths, exits, exit signs and fire extinguisher locations.
- A flame-resistance certificate for the tent fabric, often to an NFPA 701 standard.
- Occupant load and seating, if any.
- Details of any cooking, heaters or open flame, which usually must be kept outside or separated.
Rules vary a lot, so call the fire marshal's office early and ask what they want to see. Our guide to fire marshal floor plan requirements covers what most reviewers look for.
Step 8: Plan Load-In and Load-Out
Tent shows rarely have docks. Exhibitors unload on grass or pavement and carry or cart gear in. Schedule load-in by zone or time slot, keep vehicles out of the tent footprint once flooring is down, and mark a route that does not cross the generator area. Give each exhibitor a booth number and a map before they arrive. After the show, nothing should leave the tent until the aisles are clear and the tent crew is ready to strike.
Step 9: Budget for the Extras
As a planning list, a tent trade show budget usually includes the tent, install and removal, flooring, sidewalls, lighting, generators or power, fuel, an electrician, HVAC or heaters, restrooms, waste, security overnight, permits, insurance and staff. Price booths with these in mind. A tent show often costs more per square foot than a small hall, so compare quotes before you assume a tent is the cheaper option.
Sell Booths From the Tent Map
Exhibitors at a tent show worry about where they will be: near the entrance, under good light, close to power, out of the wind. A to-scale map answers that. With expo management software like Map D, you can draw the tent, place numbered booths around the poles and exits, and, on a paid plan, publish the map so exhibitors pick a booth and pay online while sold booths show as taken. Map D has been building since 2011, with over 1.8 million booths drawn, and the same map you send the fire marshal can be the one exhibitors buy from.
Tent Trade Show Checklist
- Set the booth count and pick a tent style with few interior poles.
- Get the vendor drawing and lay out booths, aisles and exits to scale.
- Collect exhibitor power needs and size generators and distribution.
- Book subfloor, carpet, sidewalls, lighting and climate control.
- Write a weather plan with wind limits and a named decision-maker.
- Submit tent, electrical and fire permits with the floor plan.
- Schedule load-in by zone and share booth numbers and maps.
- Walk the tent with the fire marshal before doors open.
FAQ
How many 10x10 booths fit in a 40x100 tent?
As a planning example, a 40x100 tent holds roughly 20 to 26 booths of 10x10 with a perimeter row on each long side, a center row of back-to-back booths and two 10-foot aisles. The real number depends on pole positions, exits, entrances, any stage or food area and what your fire marshal requires. Draw it to scale before you sell anything.
Do you need a permit to hold a trade show in a tent?
Usually, yes. Many cities and counties require a temporary structure or tent permit above a set size, and the fire marshal often inspects the tent before doors open. Expect to submit a site plan, a floor plan with exits and aisles, and a flame-resistance certificate for the fabric. Check your local rules early, because review can take weeks.
What flooring do you need for a tent trade show?
On grass or gravel, most organizers rent a subfloor of interlocking plastic or wood panels, often covered with carpet or turf. It keeps exhibitors dry, levels the booths and makes the space easier for wheelchairs, carts and strollers. On paved lots, carpet or nothing at all can work, but check that tent anchoring and cable ramps leave a smooth path.
What happens to a tent trade show if the wind picks up?
Your tent vendor should give you the wind limit for the structure as installed. Write an evacuation plan with a named decision-maker, a wind speed that triggers clearing the tent, a place to move people and a way to announce it. Check forecasts the week before and every morning of the show.

